Tideflex TF-1 Valve
FLAT-BOTTOM SLIP-ON DUCKBILL CHECK VALVE
CONTACT MEASURIT FOR A QUOTE
Reliable backflow prevention
Minimal bottom clearance required
100% elastomer construction eliminates maintenance
Will not corrode, warp or freeze open or shut
1”-2” Cracking Pressure, Low Headloss
Curved Bill enhances sealing around debris
Custom built for each application based on pressure and flow conditions
Available in diameters from 4" (100mm) to 72” (1800mm)
The TF-1 valve has become the preferred Tideflex configuration for outfalls. Designed for in-structure and end-of-pipe installations, the TF-1 features a flat bottom and flared top. This allows the valve to be installed at a lower overall elevation than other configurations, with less bottom clearance required. This is especially important in low-lying areas where maintaining as much driving head is critical, or where silt, sand and debris might tend to collect beneath the valve.
The TF-1 valve is ideal for manhole applications, such as junction boxes, diversion chambers and interceptors, where the invert of the pipe is close to the floor of the vault. These vaults are designed to maximize the available gravity head; thus, the invert pipe is as close to the floor as possible. The TF-1 allows installations in such structures and are easily retrofit to existing structures, often replacing failed flap valves, without the need for breaking up the concrete floor to provide bottom clearance.
The TF-1 valve installation instructions can be found here.
The TF-1 valve data sheet can be found here.
The Tideflex Duckbill Check Valve is a revolutionary design for backflow prevention. Tideflex Valves are a one-piece rubber matrix of numerous natural and synthetic elastomers and ply reinforcement, similar in construction to a truck tyre. Tideflex valves are cost-effective because they do not need periodic maintenance or repair to keep them operational and they have a 30 year operational life span. Tideflex operate using line pressure and backpressure to open and close so no outside energy source is required. The valve has an extremely low cracking pressure so the valve self-draining which eliminates standing water and maximizes storage volume in the upstream pipe.
Tideflex Valves have low headloss, they do not rust or corrode and are not affected by UV so performance and reliability is constant throughout the life of the valve. The flexibility of the Tideflex allows the valve to compress around trapped solids providing a much better seal than flap valves, as confirmed by the USEPA. With the development of the patented curved bill, sealing capabilities are even further improved because the curved bill is more flexible than the rest of the valve and therefore compresses more around solids.
The TF-1 installs by slipping over the end of an exposed piece of pipe, and is fastened with compression clamps. The inside diameter of the TF-1’s cuff is fabricated to exactly match the outside diameter of the pipe
The original Tideflex design, the TF-2, has a flare on the top and bottom of the valve. It has been superseded by the TF-1 and has been standardised by many consultants and owners. The patented TF-1 design is a product of 25 years of experience, research and development and testing elastomeric "duckbill" check valves. In addition to the benefits provided by a flat-bottom valve, the TF-1 also benefits from the increased angle of the upper "spine". The inherent geometry and construction of the TF-1 yields a more durable check valve with greater strength to support not only the weight of the valve itself, but the weight of the water discharging from it. In large diameter valves, this weight can amount to several tons!
The TF-1 can also be installed on the OD of elliptical pipes and many arch pipes. Tideflex Technologies also offers a thimble plate option allowing the slip-on TF-1 to be installed directly to a headwall or seawall. However, you may find that MeasurIT's R7F valve may offer a more practical and cost-effective local solution.
For higher backpressure ratings or to lower headloss while maintaining backpressure ratings, the Saddle Support Technology (SST) can be used in conjunction with the Series TF-1.
US Patent No. 5,931,197
Return to Tideflex Duckbill Valves general page.